Arched & Curved Windows in Naples, FL

Every visit starts with

Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style

Styles & brands we work with

‹

›

Before & after – our own jobs

‹

BeforeAfter

BeforeAfter

BeforeAfter

›

Arched & Curved Windows in Naples, FL

Arched and curved windows in Naples, FL are custom-fabricated openings – semicircular, elliptical, eyebrow, or full-radius shapes – measured and ordered to fit your exact rough opening, then installed with the same weatherproofing discipline we apply to every other unit in the house. Most jobs run from one window to a coordinated set across a front elevation, and the majority are completed in a single visit once the unit arrives from the manufacturer. If you have a fogged arch over your entryway, a cracked radius sash in a Florida room, or you’re building something new that needs a true curved unit from the start, call us at (239) 326-9942 – a live person answers around the clock.

TruePane Windows & Doors has been handling custom and geometric work across Naples for over 42 years, and curved openings are a meaningful part of that. They demand a different level of care than a standard rectangle: the measurements are tighter, the rough opening tolerances are narrower, and the glazing compound has to seat cleanly against a curved frame edge rather than a straight one. Dale Kessler built TruePane on the rule that if the pane is not true, the job is not done – and that rule applies here as much as anywhere. Our Custom & Geometric Windows in Naples service covers the full range of non-standard shapes we fabricate and install, and arched and curved units sit at the more technically demanding end of that spectrum.

When You Need Arched & Curved Windows

Naples homes – especially those built in Port Royal, Aqualane Shores, and the older estates along Gordon Drive – were often designed with arched transoms and curved sidelites as architectural signatures. When those units fail, finding a replacement that fits the original opening and matches the surrounding trim is not a job for a company that only stocks rectangular inventory. Here are the situations we see most often:

• Failed seal on an arched transom: The curved corner joints in an insulated glass unit are the first place argon gas migrates out. When that happens, you get the familiar grey fog that never clears – and because the shape is non-standard, a big-box replacement unit will not fit. We custom-order the IGU to the original radius and replace only the glass pack if the frame is still sound.
• Cracked or broken single-pane radius glass: Older Naples homes – particularly those built before 1990 in neighborhoods like Coquina Sands and Old Naples – frequently have single-pane arched units that were never upgraded. A crack from a storm or impact means fabricating a new curved lite to the original template.
• Drafts and air infiltration around a curved frame: Southwest Florida’s summer humidity and the pressure differential from afternoon thunderstorms push air through any gap, and a curved frame that has shifted slightly over forty years will show infiltration at the crown and at the spring points where the arch meets the jamb. We measure and diagnose before we quote.
• Upgrading to impact-rated glass in an existing arch: Many Naples homeowners in flood zones and coastal areas are catching up on impact compliance. A curved opening that was glazed with standard glass can often be reglazed with laminated impact glass within the existing frame, depending on the frame’s structural condition and the radius involved.
• New construction or remodel requiring a custom radius unit: If you’re adding a room or restoring a historic Mediterranean Revival facade in the Olde Naples historic overlay area, we can source and install curved units from manufacturer lines including CGI and CWS that meet both the design intent and the current Florida Building Code requirements for wind load.
• Deteriorated glazing compound on a wood-framed arch: Wood frames in Naples’s salt air environment dry and crack faster than manufacturers’ schedules assume. When the glazing compound around a curved lite pulls away, water gets in before the next season ends. We reglaze, re-prime, and seal to a standard that holds.

Our Arched & Curved Windows Process

Curved openings do not tolerate shortcuts in the measurement stage. A rectangular window is forgiving by comparison – you can shim a few millimeters at the sill and no one notices. A radius unit that is off by even a small margin at the crown of the arch will show a visible gap, a mismatched trim line, or a seal that cannot compress correctly. Our process reflects that reality from the first visit forward.

1. Template and field measurement: We use physical templates – not just a tape measure – for every arched and curved opening. We trace the existing frame or rough opening, record the spring-point height, the radius, the chord width, and the sill condition. For elliptical and eyebrow shapes, we take additional measurements at multiple points across the arc. This template travels with the order to the manufacturer so the unit is fabricated to the actual opening, not a nominal size.
2. Manufacturer selection and side-by-side quote: We are authorized installers for more than a dozen lines, including CGI and CWS for curved and radius work common in coastal Florida applications. We lay the quotes on paper side by side – frame material options, glass pack specifications, impact ratings, and warranty durations – so you can see exactly what you’re buying before a deposit changes hands. The Keystone Standard means both warranty layers are registered in writing before the truck leaves your driveway.
3. Rough opening preparation: Before the unit arrives, we inspect the rough opening for rot, moisture intrusion, and structural integrity. Naples’s humidity and the proximity to salt water accelerate wood deterioration, and a new curved unit set into a compromised buck will fail sooner than the warranty allows. We address the opening first. That is not an upsell – it is the reason the job holds.
4. Installation to tolerance: Arched units are set from the sill up, with the radius centered in the opening and shimmed level before any fasteners are driven. We check plumb at the jambs and verify the crown alignment against the template before the frame is secured. Flashing and sill panning follow the manufacturer’s installation requirements – both because it protects the opening and because it is required to keep the warranty valid.
5. Glazing and weatherseal: Where the unit is site-glazed rather than factory-glazed, the compound is applied in continuous contact around the full arc with no bridged joints at the spring points. We do not leave gaps at the corners and call it close enough. The seal has to be complete – any break in the bead is a place where Naples’s driving rain finds its way in.
6. Final inspection and warranty registration: We inspect the unit from inside and outside, operate any operable sash, and verify the weatherstripping seats correctly across the arc. Both manufacturer warranty layers are registered before we leave. You receive written confirmation of the warranty durations – not a vague reference to “manufacturer terms” – and our 90-Day Done Right Promise covers the workmanship from that day forward. If something is not right within 90 days, we make it right. No paperwork fight, no fine print.

Arched & Curved Windows Pricing in Naples

Arched and curved windows cost more than equivalent rectangular units, and the reason is straightforward: the glass is custom-cut to a radius, the frame is custom-fabricated, and the installation takes more time. There is no honest way to give a flat price without measuring the opening, but we can give you the ranges that reflect what Naples homeowners are actually paying for this work.

Several factors push costs up or down in Naples specifically. Homes in flood zones along the coast – Pelican Bay, Park Shore, and the barrier island properties on Gulf Shore Boulevard – often require impact-rated glass as a condition of insurance or HOA covenants, which adds to the glass pack cost but reduces the long-term risk significantly. Historic overlay districts in Olde Naples may require a particular frame profile or exterior finish to meet review board standards, which affects manufacturer selection and lead time. And any opening where we find moisture intrusion or rot in the rough framing before the unit arrives will need remediation before installation, which affects the final total.

The $50 Off Any Repair Over $250 discount applies to qualifying curved-window repair work, and our permanent 5% discount for seniors and veterans is applied at the estimate stage. Estimates are free and come with no pressure to decide on the spot. Call (239) 326-9942 and we’ll schedule a measure visit at a time that works for you.

FAQs – Arched & Curved Windows

Can a fogged arch-top transom be reglazed, or does the whole unit have to come out?

In most cases, a fogged insulated glass unit in an arch-top transom can be replaced without removing the full frame – provided the frame itself is structurally sound and the seal between the frame and the rough opening is intact. We assess the frame on-site: if the wood or vinyl is holding its shape, maintaining a consistent radius, and showing no signs of moisture infiltration at the perimeter, we’ll order a replacement IGU to the template of the existing opening and reglaze in place. That is typically the faster and less expensive path. If the frame has shifted, cracked at the spring points, or shows rot from Naples’s humidity, a full unit replacement is the more durable repair. We won’t talk you into a replacement you don’t need, and we won’t leave you with a reglaze that’s going to fail in two seasons. Call (239) 326-9942 for a free on-site assessment.

Do arched windows in Naples need to be impact-rated?

Whether an arched or curved window requires impact-rated glass depends on the specific location of the home, the year it was built, and any HOA or insurance requirements that apply to the property. Homes in the High-Velocity Hurricane Zone – which covers most of coastal Collier County, including Naples proper – built or permitted after 2002 are generally required to meet Florida Building Code wind-load and impact standards. Older homes undergoing renovation may trigger the same requirement depending on the scope of work. Many homeowners in Pelican Bay, Moorings, and Gulf Shore corridor properties also carry insurance policies that require impact glazing as a condition of coverage. We review the applicable requirements for your address before we quote and build the right specification into the estimate from the start. Call (239) 326-9942 and we’ll sort it out before a deposit is discussed.

How long does it take to get a custom arched window fabricated and installed?

Lead time on a custom arched or curved unit from manufacturers we work with – including CGI and CWS for impact-rated coastal applications – typically runs three to six weeks from confirmed order to delivery in the Naples area, depending on the complexity of the shape and current manufacturer schedules. Simpler semicircular transoms at standard radii sometimes come faster; complex ellipticals or eyebrow shapes with custom frame profiles take longer. Once the unit is on hand, installation for a single arch-top transom is usually done in half a day. A coordinated set of curved units across a full front elevation takes a full day or more. We give you a realistic lead time when we quote – not an optimistic number that sets up a frustrating wait.

What is TruePane’s 90-Day Done Right Promise, and does it apply to curved window installations?

Yes, the 90-Day Done Right Promise applies to every installation we do, including arched and curved window work. It means that if anything about the installation – the set, the seal, the weatherstripping, the flashing – is not performing correctly within 90 days of completion, we come back and make it right at no charge. No paperwork to file, no argument about whether the issue falls under workmanship or materials. The promise is in writing and it covers the work. Separately, both manufacturer warranty layers – the glass pack and the frame – are registered in writing under The Keystone Standard before the truck leaves your driveway, with the durations stated on paper so you know exactly what you have. That is the standard on every job Dale Kessler’s team runs, and it does not change based on the shape of the opening.

Why Naples Homeowners Call TruePane for Curved Windows

The homes in Naples that have arched and curved windows are, by and large, homes that were built with care and have been maintained with care. The owners are paying attention to what goes into them. A curved opening that gets a near-enough repair – a rectangular unit shimmed awkwardly into an arch, a reglaze that bridges rather than fills at the spring points – shows. It shows in the light gap at the crown, in the caulk that cracks before the next rainy season, in the trim that does not sit flat.

Over 42 years of work in Naples and the surrounding communities, Dale Kessler and the TruePane team have built a reputation on that kind of attention. We train apprentices into journeymen here, we hire locally, and we plan to be answering the phone in this community thirty years from now. That is the context in which our 90-Day Done Right Promise and The Keystone Standard exist – not as marketing language, but as the operational baseline that makes it possible to stand behind the work when a customer calls back.

If you have a curved or arched window in Naples that is fogged, cracked, drafting, or simply past its service life, the first step is a measure visit and a straight conversation about what the repair or replacement actually involves. Our estimates are free, our pricing is upfront, and there are no surprise line items on the final bill. We are an authorized installer for manufacturer lines including CGI and CWS, and we carry both warranty layers for every unit we install. The pillar of everything we do starts on the home page – but the work is done here, in your house, by people who treat it accordingly.

Call (239) 326-9942 – a live person will answer, any time of day or night, and we will get you scheduled for a free estimate at a time that suits you. If the pane is not true, the job is not done – and that is the standard we hold ourselves to on every arched and curved window we touch in Naples.

Key Takeaways

• Arched and curved windows are custom-fabricated to the template of your actual opening – nominal sizes do not apply here.
• Most Naples coastal properties require impact-rated glass in curved openings; we confirm the applicable code requirement before quoting.
• Reglazing an existing sound frame is often less expensive than full replacement – we assess on-site and recommend what the opening actually needs.
• Lead time from a confirmed order to installation typically runs three to six weeks for custom radius units in Naples.
• Every installation is covered by the 90-Day Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing before we leave.
• Seniors and veterans receive a permanent 5% discount; qualifying repairs over $250 qualify for $50 off.
• Estimates are free, pricing is upfront, and a live person answers at (239) 326-9942 around the clock.

Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Naples.